However, care must be used with this method to ensure you do not force the toothpick through the lens cloth, which can damage the lens coating if excessive force is used.ģ.If is simply dust or pollen that needs to be cleaned from the surface of the lens, you can also use compressed air spray cans that are used to clean dust from electronics or computer keyboards. You may also want to add a drop of lens cleaning solution to the lens cloth as well. Then, drape a lens cloth (#642, Soft-Tek Micro Fiber Lens Cloth works well) over the flattened end of the toothpick, and use that to clean the lens. This now creates a small, flat surface on the toothpick. To use the lens paper or cloth, you will need to fold it up into a “point” to get into the surface of the lens.Ģ.Another method is to use a toothpick, and clip the pointed end of the toothpick off using a fingernail clipper. Once the lens is clean, it can be dried with the opposite end of the foam applicator, or some other lens cleaner such as lens paper or our Soft-Tek Micro Fiber Lens Cloth (#642). The best ways we have found to clean the lenses are as follows:ġ.Using our Lens Brite Anti Fog Lens Cleaner (#641) and Foam Applicator Lens Cleaner (#501), place a drop of the lens cleaner on one end of a foam applicator and clean the lens using that. Just remember that the Clarifier or Verifier lens is just like the lens in your binoculars and riflescope, and care should be used when cleaning. Super D (#1011) or Versa³ (#V33D): 3/32”, 1/8”, or Large apertureĬleaning Verifiers and Clarifier lenses can indeed be difficult due to the small areas of the lenses. To select the hole size for your Clarifier, you should select one that frames your scope housing. A compromise between a blurred dot or clear target is sometimes necessary. You can compensate for this by using a larger aiming dot, or by using a brighter dot such as a fiber optic pin. Keep in mind the stronger the clarifier, the more it will make your aiming dot blurry. To select the correct clarifier power, see suggestions below:Ģ power lens we suggest trying #0.5 or #1 Clarifierģ power lens we suggest trying #0.5 or #1 ClarifierĤ power lens we suggest trying #0.5, #1, #1.5 or #2 Clarifierĥ power lens we suggest trying #0.5, #1, #1.5 or #2 ClarifierĦ power lens we suggest trying #1, #1.5 or #2 Clarifierħ power lens we suggest trying #1.5, #2 or #3 ClarifierĨ power lens we suggest trying #2 or #3 Clarifier The following link will take you to our Dealer page. The best way to choose the correct Clarifier power is to find an archery dealer that has our Clarifier Tool. If you are using a peep with a certain aperture hole size, we recommend using the same size when selecting a clarifier. The first step in using a clarifier is to choose the correct hole size (see Aperture section).
Scope housing has machined track/groove to facilitate proper scope alignment.Ĭlarifiers are available in 5 powers, and in 6 different hole sizes. Mounts using standard 10/32 scope mounting rod. As a result, the lens may become damaged unless the black plastic Lens Clamp is used. If the scope is used without an accessory, the lens will not be secured sufficiently, and it will rattle within the scope housing. NOTE: the included black plastic Lens Clamps MUST be used if the scope is used without a Scope Shade or other accessory. Lenses can be installed into front or back of scope housing, or both if configured for Double Vision use.Īccessories (such as the Scope Shades, Rheostat Fiber Ring, etc.) have indexing tabs that fit into indexing notches in the Versa² and Versa³ scopes to ensure proper alignment. The larger Versa² 3D works with the Specialty Archery 1.750” diameter lens, and is best suited for 3D shooting, or for archers who prefer a larger diameter field of view. Smaller Versa² Target for target and spot shooting, works with the Specialty Archery 1.345” diameter lenses (both positive power lenses and Double Vision lenses). The new Versa² and Versa³ scopes can be used in either RH or LH configurations. NEW – Innovative knurled Red Clamp Ring attachment system allows for attachment of a wide variety of different scope accessories such as Scope Shades, a Rheostat Fiber Ring, or the new 007 UV Light Half Shade. There are many benefits of the Versa² Target and Versa³ 3D scopes:
0 kommentar(er)
